• Electronic Bidet Seat: the Serena electronic bidet seat is supplied with the suite, adding a warm-water cleansing shower, a heated seat and a night light to a classically simple rimless toilet.
• Front Wash and Rear Wash: turn the control dial one way for the rear wash and the other for the front wash, and the stepless dial varies the flow from gentle to strong.
• Instant Water Warming: three water settings (normal temperature, about 35°C and about 38°C) give a comfortable wash, and the water is warmed instantly as it is used.
• Heated Seat: three seat settings (room temperature, about 33°C and about 37°C) keep the seat comfortable on cold mornings, with a low-temperature protection mode that eases the seat to about 29°C five minutes after sitting.
• Adjustable Shower Spray: a stepless control dial gives an adjustable, gentle showering function, with water volume of 0.7L per minute or less at a water pressure of 0.18MPa.
• Night Light: a night light stays on while the seat is powered, so the bathroom is easy to find at night without switching on bright lights.
• Soft Close Seat and Lid: the seat and lid lower slowly and quietly, and the low-profile, minimalistic seat design suits both contemporary and classic bathrooms.
• Antibacterial Nozzle and Seat: the nozzle and seat are made from antibacterial material, and the nozzle cleans itself automatically after use.
• Safety Protections: the water shuts off if its temperature goes above 43°C, an alarm sounds if you stand up without turning the dial off, and the seat carries an integral high hazard protection device (AVB) tested to AS 2845.1:2022.
• Quick-Release Seat: press and hold the release button and slide the seat forward to lift it from the bracket for cleaning or storage.
• Rimless Bowl: the open rimless bowl, with the Easy Clean ceramic glaze, is designed for maximum cleaning of the inner bowl.
• Universal Trap Connection: connects to either a P-trap or an S-trap, with the PN0030 S-trap connector included and an S-trap set-out of 55 - 175mm.
• Flexible Water Inlet: the suite offers a back inlet at 730mm height FFL or a bottom inlet left or right, and the bidet seat connects through a bottom inlet.
• Use During a Power Failure: the water and seat temperature cannot be adjusted when power is cut off, but the bidet can still be used with water at normal temperature.
• Water-Efficient Dual Flush: a 4 star WELS rating with a 4.7L full flush and 2.9L half flush, averaging 3.3L per flush.
• Manufacturer's Warranty: Parisi covers ceramic toilet pans, cisterns and bidets with 10 years' replacement product cover, including one year's labour.

• Control dial - rear wash: turning the dial clockwise starts the rear wash. Cold water runs from the front of the nozzle for about 5 seconds, then the nozzle extends and sprays, and the flow rises as the dial is turned further.
• Control dial - front wash: turning the dial anticlockwise starts the front wash with the same 5 second lead-in, and the flow varies with the rotation of the dial.
• Stop position: return the dial to the centre STOP position after rinsing to prevent splashing; the indicator light flashes while the bidet is working.
• Water temperature key: the water temperature key on the seat cycles through off, normal temperature, about 35°C and about 38°C, with a one second beep when the setting changes and a two second beep when it is switched off.
• Seat temperature key: the seat temperature key cycles through off, room temperature, about 33°C and about 37°C in the same way.
• Self-cleaning nozzle: the nozzle closes automatically after a 5 second self-clean during use, and a 2 second self-clean after the rinse cycle finishes.
• Standby and self-check: when power is connected the seat self-checks and beeps, the dial lamp and night light stay on, the water temperature defaults to about 35°C and the seat to about 33°C, and standby power use is about 1 kWh per month without seat heating.
• Low-temperature seat protection: five minutes after you sit down, the seat switches to a low-temperature protection mode of about 29°C.
• Alarm function: if you stand up after using the seat without turning the controls off, an alarm sounds until the dial is returned to the off position.
• Water temperature protection: if the water temperature goes above 43°C during use, the water turns off and the seat switches to self-cleaning mode, then resumes once the temperature returns to normal.
• Use during a power failure: water and seat temperature cannot be adjusted without power, but the seat can still be used with water at normal temperature.

• Product Type: Toilets
• Brand: Parisi
• Collection: Serena
• Range: Design
• Designer: Parisi Design Team
• Material: Ceramic
• Colour / Finish: Gloss White
• Glaze: Easy Clean ceramic glaze
• Rimless: Yes
• Seat: Serena electronic bidet seat EC105 (bottom inlet)
• Seat Features: Front wash, rear wash, adjustable water temperature, adjustable seat temperature, night light, soft close seat and lid, antibacterial nozzle and seat
• WELS Rating: 4 Star, 4.7L / 2.9L
• Average Flush: 3.3 Litres
• WELS Registration Number: L08023
• WELS Licence Number: 0022
• Trap Options: Universal trap (P-trap or S-trap)
• P-Trap Set-Out: 185mm height FFL
• S-Trap Set-Out: 55 - 175mm using PN0030 connector (included)
• Inlet Options: Back inlet 730mm height FFL; bottom inlet left or right
• Fixing Type: Floor
• Rated Voltage: 220-240V~, 50/60Hz
• Rated Power Consumption: 960W (entering water temperature 15°C, flow rate 6000ml/min)
• Maximum Power Consumption: 1550W at 220V
• Power Cord Length: 1.5m
• Protection Class: IPX4
• Water Supply Pressure: 0.1 - 0.5MPa (150 - 500kPa recommended)
• Water Supply Temperature: 4 - 35°C
• Ambient Temperature: 4 - 40°C
• Water Volume: 0.7L per minute or less at 0.18MPa, stepless regulation
• Water Temperature Settings: 3 settings (normal temperature, 35°C, 38°C)
• Water Heater Power: 1500W at 220V
• Seat Temperature Settings: 3 settings (room temperature, 33°C, 37°C)
• Seat Heater Power: 50W at 220V
• Certification: WMTS 051:2021 (WMK26885)
• Warranty: Ceramic toilet pans, cisterns and bidets: 10 years' replacement product cover, including one year's labour

• Installation type: Floor mounted wall faced suite with an electronic bidet seat connected through a bottom inlet.
• Trades required: the suite and seat must be installed by a licensed plumber and a licensed electrician, following Parisi's installation instructions.
• Plumbing standards: install with appropriate backflow protection conforming to the National Construction Code Volume 3, in accordance with AS/NZS 3500.2 and the Plumbing Code of Australia.
• High hazard protection: the seat has an integral high hazard protection device (AVB) tested to AS 2845.1:2022; local authorities may have varying requirements, so check whether an RPZ valve is required.
• Water supply: connect to a domestic potable water supply only, with pressure not exceeding 500kPa (150 - 500kPa recommended) and supply water between 4°C and 35°C. Do not connect hot water above 40°C.
• Isolation valve: fit an angle or mini stop valve close to the product so the water can be turned off for maintenance, and flush all water lines of debris before final installation.
• Water connection: use the new hose assembly supplied with the seat and do not reuse an old hose; connect the water first, check for leaks, then connect the power.
• Power supply: 220-240V~ 50/60Hz, class 1 appliance that must be earthed, on a circuit protected by a residual current device (RCD) of 30mA or less.
• Power connection: use the 1.5m cable and plug supplied in a waterproof socket located away from splashing water such as a bath or shower, or hardwire the seat through an isolating switch in the bathroom if the supplied cable and plug are not used. Check wet area zones with your electrician.
• Room temperature: do not install the seat in a room where the temperature will fall below 4°C, and keep it out of direct sunlight, which can discolour the seat or destabilise its temperature.
• Trap connection: universal trap; P-trap set-out 185mm height FFL, or S-trap set-out 55 - 175mm using the included PN0030 connector.
• Handling: leave the protective film on the seat until installation is finished, and do not stand or sit on the seat or lid.

Parisi Warranty

Brand Introduction

Parisi products are backed by a comprehensive manufacturer's warranty against defects in materials and workmanship, reflecting the brand's confidence in the quality and function of every product.

The periods below apply to residential use. Commercial warranty periods differ; contact Parisi for details.

Warranty Coverage

Tapware and Mixers

• Ceramic disc cartridges, taps, outlets and mixers: 15 years' replacement product cover, including five years' labour.
• Chrome and PVD finishes: 15 years, subject to warranty conditions.
• Electroplated matt black finishes: Five years, subject to warranty conditions.
• Sensor tapware: One year for parts and labour.
• Kitchen pull-out sprays and hoses: One year for parts only.

Showers

• Overhead showers, arms, rails and columns: 15 years' replacement product cover, including five years' labour.
• Handshowers, hoses, sliders and diverters: One year replacement product warranty.

Accessories and Heated Rails

• Accessories and heated rails: 15 years' replacement product or parts cover, with five years on electronic components.
• Sensor accessories: One year for parts and labour.

Basins and Toilets

• Ceramic and solid-surface basins and ceramic butler sinks: 10 years' replacement product cover, including one year's labour.
• Ceramic toilet pans, cisterns and bidets: 10 years' replacement product cover, including one year's labour.
• Geberit valves: Three years' replacement product cover, including one year's labour.
• Moda and Pressalit toilet seats: 10 years' replacement product cover, with one year on moveable parts.
• Selected toilet seats: Five years' replacement product cover, with one year on moveable parts.
• Standard toilet seats: One year for parts only.

Concealed Cisterns

• Concealed cistern tanks: 15 years' replacement product cover, including one year's labour.
• Push panels: Two years' replacement product cover, including one year's labour.
• Internal components and sensor flush panels: One year for parts and labour.

Baths

• Stonetec® baths: 25 years' replacement product cover.
• Lucite® acrylic and steel-enamel baths: 15 years' replacement product cover.
• Acrylic inset baths: 10 years' replacement product cover.

Sinks

• Stainless steel sinks: 20 years' replacement product or parts cover.

Bathroom Furniture

• Cabinets and ceramic or quartz-stone tops: 10 years' replacement product cover, including one year's labour.
• Cabinet handles: Five years' replacement product cover.
• Mirrors and mirror cabinets: One year for the replacement product and electrical components.

Doorware

• Handles, knobs, locks and latches: Five years' replacement product cover, including one year's labour.
• PVD finishes: 15 years, subject to warranty conditions.
• Stainless steel and chrome finishes: 10 years, subject to warranty conditions.
• Electroplated matt black finishes: Five years, subject to warranty conditions.

Proof of purchase is required for every warranty claim. The warranty applies only to the original purchaser and is not transferable.

What's Covered

• Manufacturing defects in materials and workmanship.
• Repair, replacement or refund of a defective product at Parisi's discretion.
• Replacement of defective parts within the applicable warranty period.

What's Not Covered

• Incorrect installation or failure to follow the manufacturer's instructions.
• Installation by an unlicensed tradesperson.
• Misuse, abuse, accidental damage or neglect.
• Damage caused by abrasive cleaners, bleach, or acidic or ammonia-based products.
• Damage caused by poor water quality, excessive water pressure or inadequate plumbing preparation.
• Normal wear and tear, including seals and O-rings.
• Water damage to bathroom furniture.
• Repairs or modifications carried out by unauthorised parties.
• Ex-display products.

Conditions

• Tapware, basins, toilets and showers must be installed by a licensed plumber.
• Products must be installed in accordance with the manufacturer's instructions and Australian Standard AS/NZS 3500.
• Water pressure must not exceed 500 kPa. A pressure-limiting valve must be installed where required.
• Products must be inspected for transit damage before installation.
• Products must be maintained and cleaned in accordance with Parisi's care instructions.
• Proof of purchase must be provided with every claim.
• The warranty applies only to the original purchaser.

Making a Claim

Warranty claims should be made through the original place of purchase. Claims may also be lodged through the Parisi warranty claim page. Have your proof of purchase and photographs of the issue available when submitting a claim.

Australian Consumer Law

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if they fail to be of acceptable quality and the failure does not amount to a major failure.

The PN76B is the Serena suite supplied complete with the Serena electronic bidet seat, so the heated seat, adjustable warm-water wash and night light arrive with the suite rather than as a separate purchase. The seat is the same Serena bidet seat that Parisi lists on its own as the EC105 bottom inlet model, and its simple dial-and-two-key controls keep everyday use easy for every member of the household.

Plan the electrical and plumbing work together. The seat draws a rated 960W with a 1500W instant water heater and a 50W seat heater, and it needs a protected power point or an isolating switch within reach of the installer, as well as a water supply with an angle valve close to the pan. The quoted standby use is about 1 kWh per month with seat heating off, and the installation instructions also set out the backflow protection, RCD and wet area requirements that your plumber and electrician will work to.

Looking after the suite is straightforward. The nozzle cleans itself automatically, the filter screen can be removed and rinsed when water flow drops, and a monthly check of the surge protector keeps the seat operating safely. Wiping with a soft cloth, warm water and a neutral detergent, and keeping chlorine-based and abrasive cleaners away from the seat and hinges, will keep the Gloss White finish looking fresh.

• Suite: Parisi PN76B Serena Smart Toilet Suite in Gloss White.
• Bidet seat: Serena electronic bidet seat EC105 (bottom inlet) with soft close seat and lid.
• Seat fixing kit: Installation template, fixing plate, screws, expansion bolts, nuts and adjustment sheets.
• Water connection: Water inlet hose with filter screen.
• Power: 1.5m power cable and plug.
• Connector: PN0030 S-trap connector.

• PN76B SPECIFICATIONS SHEET (PDF)
• SERENA BIDET SEAT INSTALLATION INSTRUCTIONS AND USER MANUAL (PDF)
• PN76B WELS CERTIFICATION (PDF)